Dynemech range of vibration control products Follow Machine Mounts Manufacturer on Facebook Follow Anti-Vibration pads Manufacturer on Twitter Vibration Mounts - Machine Mounts discussions on Blogspot Dynemech range of vibration isolator
 


Dynemech Foundation Isolation - Zeiss CMM

Machine Details:

Isolated foundation for Carl ZEISS CMM make contura G2

X/Y/Z measuring - 700/1000/600 mm

Machine Weight: 1550 Kg.





Dynemech Foundation Isolation Calculations:

Size of concrete

block

1900mm x 2200mm x 1000mm.

Total weight of Machine

& Concrete Block

12000Kgs.
Foundation Pit Size 2100mm x 2400mm x 1100mm.

Foundation Isolation

Solution

Dynemech's Foundation Insulation Sheet - 75mm thick.
Zeiss Contura G2 CMM Foundation Isolation Solution provided by Dynemech
 
Fig: Zeiss Contura G2 CMM


Foundation Isolation Solution provided by Dynemech


 
Dynemech Isolated Foundation CMM
 
Fig: Line Diagram for Dynemech Foundation Isolation for CMM Machines.

Guide Lines:

  1. 1. Make a pit as per the recommended size - 2100 x 2400 x 1100 mm.
 
  1. 2. Pit should be 100% water proof; check ground water conditions.
 
  1. 3. The inner surface of the pit should be clean, dry & smooth.
 
Dynemech Foundation Isolation - Pit preparation for Zeiss-CMM
 
Fig: Pit Construction
 
  1. 4. As per the detailed layout supplied by Dynemech, place vibration damping plate set DNM Paste them to the pit base using - Pidlite SR-505 adhesive.
 
  1. 5. Place filler foam in the gaps between the Insulation plate set DNM. Paste them to the pit surface.
 
 
Dynemech Isolated Foundation Zeiss CMM-2Dynemech Isolated Foundation Zeiss CMM-2
 
Fig: Pit after placing Dynemech Insulation Sheet and Filler Foam.
 
  1. 6. In some special cases of Isolated foundation, the sides of the foundation wall are also covered with layers of our insulation sheet to prevent foundation shaking. The horizontal vibrations travelling through the foundation are fully absorbed using these insulation sheets on the side-walls.
Isolated-Foundation-Insulation-material-placed-below-concrete-block
 
Fig: Dynemech Insulation Sheets on Side walls for preventing horizontal vibrations.
 
 
  1. 7. Place PVC on the entire pit surface and side walls. Seal the overlapping joints of the PVC sheet with adhesive tape so that the concrete water should not leak in to the pit base.
 
  1. 8. Place 25mm thick wooden board layer and joint should be sealed with adhesive tape. This will act as a support for the initial concrete pour.
 
  1. 9. Place another layer of PVC sheet on the pit base and the side walls joints sealed with adhesive tape.
 
Isolated-Foundation-Wooden-Board-Placed_on_Insulation-Sheets-below-concreteIsolated-Foundation-Wooden-Board-Placement-complete-on-Insulation-Sheets-below-concreteFoundation-Isolation-Pit-Ready-After-Pvc-sheet-lining-concrete-to-be-poured
 
Fig: Pit after covering Insulation Sheets with Wooden Board and PVC sheets.
 
  1. 10. Pour concrete up to a depth of 150mm and allow it to dry, this will act as a compression plate. After drying the compression plate erect reinforcement and pour concrete in the rest of the concrete block volume. Concrete should be poured in layers of 300mm+300mm+350mm to complete a depth of 1100mm, allow each layer to dry and pour another layer.
 
  1. 11. The concrete block and the pit tub should not come in contact with each other.
 
  1. 12. Care should be taken that the concrete or concrete laced water should not leak in to the insulation plate area.
 
  1. 13. In case the side walls are not isolated using Dynemech insualtion sheets, the side gaps may be filled with rubberised cork scrap.
 
CMM Vibration Control - Foundation Isolation
 
Fig: Dynemech Isolated Foundation Solution

CMM Machine Foundation IsolationDownload Case Study - Foundation Isolation Zeiss CMM



Foundation Isolation Supplier